ID

Description

RMS-4181A

When reviewing a document, the review page is placed at the beginning of the reviewed document and not at the end. The original document will not be modified.

ID

Description

RMS-2759A

Password substitute implemented for all system passwords to ensure that saved passwords are not visible for the user.

RMS-2865A

The "Close datagap" link is visible with the data analysis, even if it is already closed.

RMS-2896A

When editing a system measuring point device refresh counter, the elements are not populated.

RMS-2915A

If an event is inhibited twice, the first inhibition remains open in the audit trail. After the inhibition expires, only the second inhibition is closed. The first inhibition event must then be closed manually.

RMS-2920A

When inhibiting an event, the duration is not accurate.

RMS-2954A

The E-Mail support system information incomplete: For Rotronic internal use only.

RMS-3029A

"Server error" message appears instead of "Access denied" when a user tries to carry out a calibration with the missing user rights.

RMS-3120A

When setting the alarm limits to off under the measuring point, the visual of the historical limits disappear from the chart/report. This is only a visual error and does not affect the data integrity of the historical alarm settings.

RMS-3121A

The Service manager crashes after 60 minutes.

RMS-3155A

PDF report: the limit violation table is empty if the alarm for the measuring point is currently deactivated, even if there are historical limit violations.

RMS-3216A

PDF report: the first 3 records are repeated after a page break.

RMS-3416A

The last adjustment values for the RMS-ADC-R-L should not be visible.

RMS-3433A

The scaling of the RMS-8ADC-L-R gets reset when the RMS-CONVERTER-100 restarts.

RMS-3436A

When adding an analogue measuring point and selecting another parameter than “analogue”, the log data cannot be assigned correctly resulting in a datagap.

RMS-3438A

A validation error will occur when data is read out from the logger once the data is already validated by the system.

RMS-3588A

Service Manager will crash after OutOfMemoryException.

RMS-3622A

The E-Mail support system information incomplete: For Rotronic internal use only.

RMS-3623A

The last refresh value on the RMS-GW and RMS-CONVERTER-100 devices are disproportionately high.

RMS-3624A

Incorrect repetition number in E-Mails and SMS's.

RMS-3625A

Incorrect repetition notification interval.

RMS-3627A

Translation error in French under inhibition.

RMS-3644A

PDF Report: Alarm zone not visible for single measure point.

RMS-3645A

PDF Report: Alarm zone no visible (out of range).

RMS-3732A

Logfile Error: CloseEventDto.

RMS-3758A

PDF Report: the battery levels appear at 255%.

RMS-3787A

Exception: Notification KeyNotFoundException.

RMS-3900A

The CSV report is empty if first measuring point has no data.

RMS-3901A

Retroactive alarms are triggered while inhibited.

RMS-3906A

Retroactive sensor error after deleting or archiving a measuring point.

RMS-3907A

Data gap closed before all data has been downloaded.

RMS-3928A

System measure points selection contains "Tristate button".

RMS-3948A

Notification continues after an inhibition.

RMS-3960A

Data analysis chart not showing values when the mouse hoovers over.

RMS-3977A

MFM920 Telephone call event not closing.

RMS-4013A

Cancelling technical alarm inhibition not working.

RMS-4015A

PDF Report: the alarm limit is incorrect when negative.

RMS-4023A

PDF Report: the wrong measure value count in shown in the data report warnings/alarms.

RMS-4028A

An out of limit violation is not detected if the values goes directly from low to high limits.

RMS-4038A

Software exception on phone call if provider plugin not selected.

RMS-4093A

Calibration report error if documents are not included in the license.

RMS-4166A

Alarm action E-Mail: details are incorrect in the audit trail.

RMS-4170A

It is not possible to add a new dashboard with Firefox.

RMS-4184A

The custom call/SMS provider is not working.

RMS-4186A

Wrong value in SMS alarm notification message.

RMS-4191A

Measuring data older than the first alarm zone will be analysed using the first alarm zone. In this case false positives can be in the report.

RMS-4305A

Readout command and datagap event creation for a device without any active measuring points.

RMS-4332A

Data gets restored even when a measuring point is disabled.

RMS-4389A

Sending of an alarm finished E-Mail when an alarm finishes before the notification delay time is passed.

RMS-4499A

The adjust function doesn’t work when the temperature is set to Fahrenheit (°F).

RMS-4506A

User cannot access RMS via the browser.

RMS-4515A

Validation function: check send E-Mail event may fail due to a timing issue.

RMS-4519A

Mapping report: an incorrect alarm zone is shown in the PDF report charts.

RMS-4527A

Calibration: an incorrect calibration report is shown under the measuring point.

RMS-4530A

Mapping and Batch Release Report: Duration and chart scale not representing the selected time frame.

RMS-4531A

Event report not saved under documents when "send E-Mail" is selected.

RMS-4532A

Inhibition: when closing a technical inhibition, the measure inhibition event is also closed.

RMS-4537A

Inhibition: when closing a technical inhibition, only the first measuring point of the device is closed.

RMS-4675A

If LDAP SyncUser setting is active, the code checks if the RoleId from LDAP is okay even when the SyncRole is not active.

RMS-4677A

New PDF reports (Configuration, Mapping, Batch/Release, Report Review) do not support font setting.

ID

Description

RMS-4536A

Report: if a report exceeds the defined data limits, the report is still created, but the user is not informed that the limit was exceeded.

RMS-4706A

Mapping Report: An Unknown Error will occur during export, if the Browser Language uses (comma ",") instead of (period ".") for floating Values e.g (1.2; 3.5)

RMS-4825A

"Database error" when opening the alarm table.