Technical specification

<< Click to Display Table of Contents >>

Navigation:  Hardware Overview > LOG Dataloggers > RMS-LOG-868/915 >

Technical specification

General - Data Logger


Device type

RMS Data Logger

Range of application

-40..70 °C / 0..100 %rh

Measured Parameters

oHumidity & temperature with HygroClip HCD-S

oDifferential pressure with PCD-S

oCO2 with CCD-S

oTemperature with TCD-S

IP protection

IP651

Storage and transport conditions

-40..30 °C / 0..90 %rh

Data memory

44,000 pairs of measured values

Interfaces        

oEthernet (RMS-LOG-L)

oWireless 868 MHz (RMS-LOG-868)

oWireless 915 MHz (RMS-LOG-915)

Protocols        

HTTP & MODBUS

Wireless range        

20..50 m, indoors 868 MHz

15…25 m, indoors 915 MHz

Transmitting power

14 dBm (25 mW)        

2 dBm (1.6 mW)

Software compatibility

≥V1.1        

≥V1.2.1

General - RMS Display


Device type

RMS Display

Range of application

-20..30 °C / 0..100 %rh

IP protection

IP651

Storage and transport conditions

-20..30 °C / 0..100 %rh

Interfaces        

Ethernet (RMS-D-L)

Protocols        

HTTP

Power supply


Supply voltage

24 VDC ±10 % / <100 mA2  

PoE: 802.3af-2003, Class 1

Battery (No battery option with the RMS-D-L)

Current consumption

<100 mA

Polarity protection

Yes

Battery life

The batteries of RMS devices typically last 3 years under the optimal conditions:

Temperature = 20°C±5°C.

Wireless signal strength >-60 dBm.

Limited “read out data” events in the audit trail.

Start Time and Measurement Interval


Start time

oLAN logger: 10 s (typical)

oWireless logger: 1 s (typical)

oLAN display: <20 s

Measurement interval        

10 s to 15 min

Refresh rate (RMS-D-L)

10 s

Housing Specifications


Housing material

ABS

Dimensions

105 x 113 x 38 mm

Weight

200 g

Conformity


EMC directives

RMS-LOG-L

EMC Directive: 2014/30/EU

LVD Directive: 2014/35/EU

 

oEN 61326-1:2013

oEN 55011:2016, class B        

oEN 55032:2016        

oEN 61010-1:2010        

oEN 50581:2012

oIEC 61326-1:2012 ed2.0 (Industrial Environment)

oIEC CISPR 11:2015; class B

oIEC CISPR 32:2016

oIEC 61010-1:2010

oIEC 50581:2013-02

 

Performance criterion: www.rotronic.com

EMC directives

RMS-LOG-868

RED-Directive 2014/53/EU

 

oEN 61326-1:2013        

oEN 301 489-1: V2.1.1

oEN 301 489-3: V2.1.0

oEN 300220-1: 2013-02 / V2.4.1

oEN 300220-2: 2013-02 / V2.4.1

oEN 62479: 2010

oEN 62368-1: 2014 + AC:2015 + Ber 1:2016-11

oEN 50581:2012        

IEC 61326-1:2012 ed2.0

 

 

 

 

 

IEC 62368-1: 2014 + Cor.:2015

IEC 50581:2013-02

 

Performance criterion: www.rotronic.com

EMC directives

RMS-D-L        

EMC Directive: 2014/30/EU

LVD Directive: 2014/35/EU

 

oEN 61326-1:2012

oEN 55011:2016, class B        

oEN 55032:2015        

oEN 61010-1:2010        

oEN 50581:2012

oIEC 61326-1:2013 (Industrial Environment)

oIEC CISPR 11:2015; class B

oIEC CISPR 32:2015

oIEC 61010-1:2010

 

Performance criterion: www.rotronic.com

FCC

RMS-LOG-915

oFCC 47 CFR part 15 subpart B: Clause 15.107 + Clause 15.109                

oFCC 47 CFR part 15 subpart C: Clause 15.249 (

oICES-003 Issue 6: Clause 6.1 + Clause 6.2                

oRSS Issue 5: RSS-102 + RSS-210

Soldering material

Lead free (RoHS Directive 2011/65/EU)

FDA/GAMP directives

FDA CFR 21 Part 11 / GAMP5

1 IP65 protection is only fulfilled, when rubber plug is used for cabling.

2 Power supply requirements: 24 VDC ±10 % / >4 W / limited power source